How to Change the Oil on a Mercedes C230


1. Locate oil filter on your Mercedes 230 and place the oil drip pan underneath on the ground. The oil filter will be found under a black cover on the driver's side of the engine, between the valve covers and the firewall. Loosen the filter with an oil filter wrench, about one full turn, to allow oil to flow back into the engine.
2. Raise the front of the car with car jack and place it on jack stands. Remove the engine covers from the bottom of the engine by using an 8 mm socket wrench. Position the oil drip pan under the oil drain plug at the rear of the engine's oil pan.
3. Loosen the oil pan plug with a 1/2-inch open end wrench and allow the oil to drain into the drain pan. When the oil is completely drained, remove the oil filter from the engine.
4. Coat the new oil filter rubber o-ring with a thin layer of oil and screw the filter back onto the engine. Tighten until the filter is snug, but do not over-tighten. Replace the oil drain plug on the drain pan and tighten it with a 1/2-inch open end wrench.
5. Remove the oil cap from the valve cover and pour 5.25 quarts of oil into the engine. Replace the oil cap and turn the key in the ignition to the 'on' position for about 10 seconds without starting the engine. This will prime the engine with the new oil. Turn engine on and run it for a couple minutes. Then turn it off.
6. Replace the engine covers on the bottom of the engine and remove the jack stands. Dispose of used oil at your local recycling center or automotive store.
Continue lendo

How to Extend My BMW Lease Agreement


1. Call your BMW lease-end relationship consultant at (800) 959-4BMW (4269) to arrange and negotiate a short-term re-lease. You may re-lease for a minimum of one year and a maximum of three years.
2. Talk to your lease-end relationship consultant about the payment and terms of your re-lease. BMW Financial Services will determine a new lease payment within about 30 days out from your current lease maturity date.
3. Sign the new re-lease agreement to keep a lease on the BMW you are driving if you are satisfied with the terms.
Continue lendo

Audi TT Fuel Flap Removal


1. Turn the Audi TT off and go to the rear passenger side where the fuel tank flap is located. Push in on the outer edge of the flap to unlatch it and pop it open.
2. Locate the three Phillips head screws that lie along the inside rim of the fuel flap collar equidistance from each other. Unscrew each screw and keep the screws somewhere safe for possible reuse. Slide a flat-head screwdriver into the seam between the inside rim and car body. The collar is also cemented onto the body panel, but it can be separated with a light rocking back and forth.
3. Pull the collar with the fuel flap off the body panel slowly as it is still attached to the door sensor. The door sensor tells the Audi TT when the fuel flap is open and when it is closed. Unplug the door sensor from the fuel flap collar and drape it down on the side. If you are going to paint the Audi TT with the fuel flap off, tape over the hole to prevent paint from sealing the gas cap shut.
Continue lendo

How to Remove an Audi Fuel Pump


1. Remove the fuel filler cap, start the car and leave it running until the fuel tank is completely empty. The engine will cut off once the fuel has run out. Turn off the ignition
2. Use the pliers to disconnect the negative battery cable. Before disconnecting the battery, ensure you have the correct security code for the car radio, as all systems will be reset once the battery is disconnected.
3. Open the trunk and remove the trunk flooring cover. Locate the fuel tank behind the rear passenger seat. Remove the cover.
4. Lift the cover. Using the 1/4-inch ratchet and socket wrench remove the nut. With the nut removed, you will gain access to the fuel pump.
5. Disconnect the harness connector, fuel supply, return hose from the flange and remove the electrical connectors. Use an old rag to catch any excess fuel from the fuel lines.
6. Turn the fuel pump counter-clockwise until it unlocks and can be removed.
Continue lendo

How to Get the Serial Number From a BMW Business Radio


For BMWs Manufactured in 2000 and After
1. Insert your key into the ignition but make sure it is in the "Off" position.
2. Locate the “M” button. In some BMWs the ”M” button will be between two arrows, one facing left and the other facing right. The "M" button is on the front of the BMW business radio with the other radio control buttons.
3. Press and hold the "M" button while turning the key. Only turn the key to turn on the radio, but do not start the car.
4. Look for the serial number on your radio display. The serial number should flash across the screen. It will not disappear unless you press other buttons on the radio to access the menu.
For 1999 and Older BMWs
5. Remove the radio unit from the chassis to view your serial number for model year vehicles 1999 and older.
6. Locate a resource or professional to properly remove the radio unit from your vehicle. The procedure for removing the radio may be slightly different, therefore, find specific instructions for your year and model. Research various sites online that will give you step-by-step instructions for removing your audio system properly to retrieve your serial number.
7. Look on the back of the chassis of your radio to locate your serial number. Your serial number will start with either "F, Pha, P, BP or AL."
Continue lendo

The Transmission Won#039;t Shift in My 2002 Mercedes


1. Put your foot on the brake and attempt to move the gear shift out of park. The park-brake interlock system will not allow you to move your car's shift stick into position unless your foot is on the brake. By applying the brake you will be able to shift freely.
2. Remove the console covering the shifter. The console can be easily removed to check for other problems if applying the brake does not work. The Mercedes-Benz has cupholders near the base of the transmission shift stick. If spilled liquid enters the shifting console it can stop it from functioning.
3. Use a clean cloth soaked in an alcohol solution to clean the inside of the stick shift. Make sure you remove any residue that might be causing the issue.
4. Locate the safety override button near the base of the shifter mechanism if these solutions fail to fix the problem. Pushing this button will override the park brake interlock system and allow you to drive your car to be serviced. If you need to resort to this step it is likely that the solenoid or cable mechanism is broken and needs repair.
Continue lendo

How to Remove the TDI Injector


1. Pop the hood. Open the gas door and remove the gas cap. Locate the injector pump, which is on the driver's side of the engine. Disconnect the fuel lines running to the injector pump and the injectors with a line wrench.
2. Unbolt the injector from the cylinder head using the 3/8-inch ratchet and the 27-millimeter deep-well socket. Take the injector out of the engine.
3. Unbolt the injector heat shield from the head with the 3/8-inch ratchet and socket.
Continue lendo

How to Reset an Airbag Light


1. Put the key into the ignition and turn the switch to the 'on' position.
2. Watch for the airbag light to turn on. It will stay illuminated for seven seconds and then shut itself off. After it shuts off, immediately turn the switch off and wait three seconds.
3. Repeat Steps 1 and 2 two more times.
4. Start the engine. The SRS light should come on for seven seconds, and then shut off and stay off. The airbag light has been reset.
Continue lendo

How to Change the Turn Signal for the BMW X5


1. Turn the headlight dial on the dash to '0.' This ensures that the power to the headlight assembly is turned off. Shut down the X5's engine; pull the hood release lever and open the hood.
2. Look at the back panel of the headlight assembly to find the turn signal. The turn signal is the outermost bub in the assembly. It's right on the edge of the interior fender liner on either side of the X5. You'll see a plastic cap.
3. Rotate the plastic cap to the left to remove it. Now you'll see the turn signal bulb.
4. Turn the bulb holder to the left to disconnect it. The bulb is now free from the assembly. Pull the connection to unplug the wiring from the bulb holder.
5. Attach the replacement bulb's holder to the wiring. It simply plugs in. Place the new bulb into the assembly and turn it to the right. Attach the plastic cap and rotate it to the right to recover the bulb holder.
Continue lendo

How to Install a Radio for an Audi A4


1. Remove the existing radio. In most cases, an Audi radio removal will require the use of European radio removal tools. These can be purchased from many auto parts stores, and may be ordered from the dealership as well.
2. Inspect the factory wiring harness. Make sure that the factory harness will plug into the aftermarket radio harness with ease. Also, check the antenna adapter to ensure a proper fit.
3. Connect the aftermarket radio harness to the vehicles radio replacement harness. Solder all connections and insulate them with heat shrink tubing or electrical tape.
4. Mount the dash kit to the vehicle using the hardware provided. In some Audi models, the dash kit will secure itself using plastic clips, and no additional hardware is required. In other models, screws are necessary. Any necessary hardware will be included in the kit.
5. Plug the aftermarket harness and antenna adapter into the vehicle. Connect the remaining end into the radio. Place the radio into the dash kit and slide the unit into place. Test the new radio thoroughly for function to ensure a proper installation.
Continue lendo

How to remove the door panels on Mercedes Benz (96


1. Remove the triangular panel near the rear view mirror. This can be removed using a standard screwdriver to pop out the retaining clip.
2. Remove screw on the door jamb. This screw holds a black metal cover.
3. Pull out the "Air Bag" badge above the door handle and remove the screw.
4. Using a flat tool, pop the bottom of the door panel which is held in place by plastic retainers.
5. You should be able to jiggle the door panel off by pulling up using the handle or lifting up the bottom of the door panel.
6. Remove the wires that are attached to the tweeter and the door lock switch.
Continue lendo

How to Set the Memory Features for the Audi


1. Turn on your car and turn on the radio.
2. Skip to the radio station that you would like to save.
3. Choose a number to save the radio station to and press the numbered button while also pressing down the 'Memory' button on the stereo.
4. Hold the two buttons until the radio beeps and the display flashes, which indicates that the radio station has been saved.
Continue lendo

How to Decode an Old BMW Radio


1. Enter your car. Insert the key in the ignition. Leave it in the 'OFF' position.
2. Locate the 'M' button on your radio. Press and hold it.
3. Turn the key to the 'On' position. Turn on the radio with the 'M' button pressed.
4. Write down the serial number that displays on your radio. Contact your BMW dealership. Ask for the unlock code.
5. Provide your serial number. Write down the unlock code.
6. Press and hold the 'Tuner' button. Enter the unlock code. Wait for the radio to turn on once you entered the code.
Continue lendo

How to Install Chrome Rings on a BMW X5


1. Purchase the chrome rings from an aftermarket vendor. Many vendors exist, so shop around for the best prices and buy the ones that you think look the best.
2. Move and park your X5 into a well lit area. Once you have moved your car, unscrew the two T10 torx screws from the top of the instrument panel.
3. Insert a flathead screwdriver between the lip of the instrument panel and the dash to gently dislodge the panel.
4. Disconnect the black, white and blue connectors on the back of the cluster. Once you have removed the connectors, press in a tab on the back of the cluster and move the release bar to fully disengage the instrument panel from the X5.
5. Put your panel face down on a clean work area free of dust and debris and locate the 5 'X' connectors. Use a pair of flat-nosed pliers and twist all 5 'X' connectors so that they are parallel to the bottom of the of the instrument panel. As you twist the 'X' connectors, use a flathead screwdriver to pry the panel apart.
6. Clean the chrome rings and snap them into place on your instrument panel.
7. Once you are finished, reassemble the instrument panel and connect it to your BMW X5.
Continue lendo

How to Join a Mercedes Car Club


1. Investigate the Mercedes car club your dealer has to offer. Dealers offer new owners membership in AMG Lounge, an online forum for Mercedes AMG owners, and the Owners Online club, an online resource for Mercedes owners. Name and vehicle identification number are required to register.
2. Join the official 'Mercedes-Benz Club of America.' Your membership fee will enroll you in the national Mercedes-Benz club and a local chapter where you can meet other Mercedes enthusiasts.
3. Surf the Internet for Mercedes clubs and forums. Online registration is usually required and fee structures depend on the website you are interested in joining.
4. Visit local 'Classic Car' clubs. Mercedes has been selling cars for over 100 years, so quite a few classic car enthusiasts are Mercedes enthusiasts.
5. Visit a local car show and ask about local Mercedes car clubs. The exhibitors may not be from your community, but they can refer you to the organization hosting the car show or club members of note in your community.
6. Ask your mechanic for club referrals, especially if you are interested in the technical side of automobiles. A Mercedes' mechanic may be the best source to guide you to the Mercedes club that best suits your needs.
Continue lendo

How to Replace the Wiper Blade Insert in an Audi


1. Lift the wiper blade arm away from the Audi windshield so it is at a 90 degree angle before attempting to replace the wiper blade insert.
2. Slide the wiper blade metal rail and insert out of the wiper arm with a pair of needle nose pliers, starting at the farthest point away from you and removing the rail toward you.
3. Pull the rubber insert out of the metal rail with the pliers and discard the rubber insert.
4. Slide the new rubber insert into the metal rail. Place the metal rail and rubber insert into the wiper arm, sliding it back into the arm the way it came out.
Continue lendo

How to Fix Audi A6 Brake Lights


1. Unscrew the lens cover on the Audi's brake light using the Phillips-head screwdriver. Once the cover is removed, unscrew the existing bulb with your hands.
2. Check the brake light socket for corrosion. If necessary, clean the interior of the socket with the plastic scrub brush and wipe it clean with the dry cloth.
3. Open the A6's trunk and lift up the interior mat with your hands. Unscrew the interior panel in the floor of the trunk using the Phillips-head screwdriver.
4. Locate the fuse panel in the middle of the trunk's interior panel. The fuse panel is green with a number of colored fuses attached to the surface. Check the brake light fuses, which are red and located in the top row of fuses, to make sure they are wired properly. Make sure the ends of the brake light wires are securely attached to the fuses. If necessary, unwind the brake light wires, strip some additional covering from the wires, and re-attach the wires to the fuses by crimping the wire ends firmly with your hands.
5. Replace the cover of the interior panel and screw it into place. Screw the replacement bulb into the brake light socket with your hands. Replace the brake light lens cover and screw it into place.
Continue lendo

How to Reset My BMW X5


1. Locate the diagnostic port located under your X5's steering wheel.
2. Plug the reset tool into the diagnostic port and allow it to turn on automatically.
3. Press the 'Reset' button on the diagnostic tool to make the tool flash your BMW's diagnostic system and clear the service indicator lights.
Continue lendo

How to Program a BMW Keyless Remote


1. Close all of the car's doors and open the trunk and the driver's side door. Sit in the driver's seat and close the driver's door behind you.
2. Insert your key into the ignition and cycle it from 'Off' to 'On' five times in five seconds.
3. Wait for a chirp to sound from the car and open and close the driver's door.
4. Press any button on your remote and wait for the light on the remote to flash to indicate successful programming.
5. Close the trunk lid to end the programming sequence.
Continue lendo

Changing the Headlights on a Mercedes W211


1. Turn off your Mercedes W211, and prop open the hood.
2. Tape around the silhouette of the bumper and the headlight bezel to protect the paint.
3. Remove the push-lock fasteners in each wheel well. Pry them out using your pliers, or use the screwdriver as a wedge.
4. Remove the two clips below the lower portion of the central grille, and pull this lower portion of the grille upward and away from the bumper to remove it.
5. Remove the four 8-mm screws from below the lower bumper.
6. Remove the pair of screws in each wheel well holding the lower bumper to the fender.
7. Pull the lower bumper off the bottom front of the vehicle, just below the larger bumper.
8. Remove the two 10-mm bolts that were revealed when you removed the lower portion of the grille.
9. Remove the 8-mm bolts between each headlight cavity.
10. Remove the 10-mm plastic nuts in the front wheel wells using the socket wrench. These plastic nuts are near the push-lock fasteners you removed earlier.
11. Pull out the interfender panel near the wheel well. Look for the small screw that secures the fender to the bumper clamp. Remove this screw with a #20 Torx wrench.
12. Remove the last two front 10-mm bolts near the central grille holding the bumper to the vehicle. You should have someone hold the bumper while you do this. Pull the bumper off the vehicle and set it down gently.
13. Remove the four 8-mm bolts securing each headlight.
14. Pull the headlight slightly out of its cavity, and disconnect the four wiring harnesses from the rear of the headlight.
15. Install the new headlight by connecting the four wiring harness and securing the headlight in the socket with the four 8-mm bolts. Remount the bumper, lower bumper and lower portion of the central grille using the fasteners you have already removed.
Continue lendo

How to Change a Cabin Air Filter


1. Locate the cabin air filter access cover. Typically it is found under the hood at the very back of the engine compartment, or under the dash on the passenger side.
2. Using your screwdriver, unscrew the cover and remove the old cabin air filter.
3. Compare the new cabin air filter to the old one to make sure it is the proper size.
4. Set the old cabin air filter aside.
5. Using your rag, wipe out the cabin air filter compartment to remove remaining dirt and dust.
6. Place the new cabin air filter in the compartment, pressing down and side to side to ensure proper fit. Some filters have a foam gasket on the underside; make sure the filter is installed correctly.
7. Replace the cabin air filter access cover.
8. Wipe yourself and the area clean with rags.
Continue lendo

How to Change Audi TT Headlights


1. First, select the new headlights you want to install. The Audi TT can use a high-intensity discharge (HID) bulb or an light-emitting diode (LED) package. Choose which one you want from an auto parts store.
2. To access the headlights, you must pop the trunk and remove the headlights from behind the casings. Open the trunk and find the back of the headlight wires. These should feed right into the middle of the headlight assembly.
3. Loosen the securing screws around the headlight connection. The connection is a small plastic piece at the end of the wires. Some twisting and maneuvering may be needed to get at the screws. Loosen all the screws but do not completely remove them.
4. Once the screws are loosened, twist the headlight connector until it pulls freely out of the headlamp case. The bulb and connector will come out together.
5. Release the headlight bulb from the connector by depressing the clip or attachment (some models may have different types of clips) and pull out the bulb.
6. Insert the new bulbs by sliding them into the connectors. Replace the bulbs in the headlamp. Turn and lock them in place behind the screws, then tighten the screws to secure them.
Continue lendo

How to Change the Timing Chain on a 525I BMW


1. Buy a timing chain that is made specifically for the BMW 525i 2.5L engine. Most auto parts store or online vendors carry the timing chain needed. Lift the hood of your vehicle and disconnect the negative battery cable. Remove the vibration damper and hub assembly to reach the upper and lower timing case covers. Remove case covers. Refer to the vehicle service or owner's manual to identify vehicle parts.
2. Use a ratchet and pinch the upper timing chain tensioner to hold it in place. Use a wrench to remove the upper timing chain sprockets. Remove the camshafts that run along the side of the timing chain. Loosen bolts holding the upper timing chain guide in place. Remove the timing chain and upper timing chain guide. Remove the ratchet holding the upper timing chain tensioner. Remove the crankshaft sprocket and tensioning rail if necessary. Remove the Woodruff key.
3. Install the new timing chain. Replace the Woodruff key and reattach the crankshaft sprocket and tensioning rail. Reattach camshaft sprockets and tighten bolts using a wrench to 16 foot pounds (22Nm). Reattach and tighten lower timing cover bolts to 6.5 to 8.0 foot pounds (9 to 11Nm). Reattach the vibration damper hub bolt and tighten to 17 foot pounds (23 Nm).
4. Replace the upper and lower timing case covers. Start the engine to make sure the timing chain is installed properly.
Continue lendo

How to Change the Brake Lights on an Audi


1. Open the trunk and pull back the carpet in the cargo luggage area.
2. Locate the nuts holding the brake light housing cover. Remove these nuts with a socket wrench.
3. Remove the housing cover and disconnect the electrical wiring from the bulb housing.
4. Turn the bulb counterclockwise to unlock it from the housing. Pull the bulb straight out of the housing.
5. Install the new bulb, reassemble the housing and replace the carpet in the trunk. Installation is the reverse of removal.
Continue lendo

How to Buy a BMW 3 Series


1. Go to the BMW USA website to familiarize yourself with the 3 Series and its options. Choose the '3' from the top of the page; click on the body style and level you wish to pursue. Keep in mind that the xDrive models offer standard all-wheel-drive, other options offer standard rear-wheel-drive.
2. Click on 'view model highlights' to view the level's standard features. Doing this saves you time at the dealership, as you'll become knowledgeable of which level you want. View 'features and specs' from the left side menu at anytime to see a break down of specifications and standard level features.
3. Click on the 'build your own' option. From here, you can build the 3 Series as you see fit. At the same time, you can view pricing for a variety of tempting luxury options. Once you're done building the vehicle, click 'print' from the right side menu so that you can use the information for shopping purchases.
4. Click 'estimate a payment' once building is complete. Choose your state from the drop down box and whether you'd prefer to lease or finance from the 'options' boxes. Options are already filled out and calculated payments do not include taxes or fees.
5. Change the down payment amount if you would like. You can also change the rate, although the rate listed is one offered as a special rate from BMW Financial Services. If you do not plan to use BMW's special offer, change the rate to one you see fit (you can check your bank's website for current new-car auto loan rates).
6. Apply online through BMW Financial Services by clicking 'apply online for finance,' if you'd prefer. Otherwise, you can contact your bank for a pre-approval to have handy when you visit the dealership. The credit application you submit from the BMW website is forwarded to a local dealer of your choice--you are asked to choose a dealer before submitting.
7. Contact the local BMW dealership you want to use once you have your pre-approval. Make an appointment or stop in with your 3 Series print-out. Ask to test drive the model you want and find the one you want to buy, whether it is the one you built or a different model built to suit your needs if you've decided on a different level.
8. Tell the BMW consultant that you have a pre-approval. If it's from a bank other than BMW Financial Services, the consultant will provide you with the information that you'll need to retrieve your check, such as the vehicle identification number (VIN) and buyer's order, which lists all pricing and total finance amount. If financing through BMW Financial Services, the dealer will have your approval on hand and will be able to complete your loan paperwork when you are.
9. Bring the buyer's order to your financing bank to complete your paperwork. Whether financing through the dealer or independently, you'll need to provide your driver's license, vehicle registration (if transferring plates), most recent paystub and proof of residency, such as a recent utility bill. Give the check to the dealer upon return for pick up, or simply sign all paperwork at the BMW dealership. Provide any down payment at this time.
10. Sign all of your state's required motor vehicle department forms, as the dealer handles all insurance, plates, taxes and registration paperwork, even if financing independently. Your consultant will explain your vehicle's options and features entirely, secure your plates and provide you with any additional vehicle or state information before you leave in your new 3 Series.
Continue lendo

How to Refresh your XM radio signal


1. Turn your XM radio on. Position the antenna -- if a standalone receiver -- facing skyward. If you are refreshing an in-car unit and you park the vehicle in a garage, pull the vehicle out of the garage.
2. Tune your XM radio receiver to station '0' and observe as an eight-digit, alphanumeric code appears on the screen -- this is the XM radio's ID. Notate this ID. Please note that SiriusXM does not use the letters 'I,' 'O,' 'S' or 'F' in radio IDs.
3. Tune your XM radio to channel '1.'
4. Log onto the internet and direct your browser to the SiriusXM website.
5. Place the pointer over the 'Help & Support' link on the top, right of SiriusXM's website, and click 'Refresh My Radio.'
6. Type your XM radio's ID in the text box labeled 'Radio ID (ESN or SID),' and click 'Send Activation Request.'
7. Wait approximately five minutes as your radio's signal refreshes. A message on the display alerts you when the refresh is complete -- the exact message varies, depending on the style of receiver.
Continue lendo

How to Reset the Brake Warning Light on a 2001 BMW 325Ci


Resetting the System
1. Sit in the front seat of your 2001 BMW 325Ci. Keep the driver's door open.
2. Insert your keys into the ignition.Turn your keys two clicks clockwise to the number '2' position to turn your BMW 325Ci's system on without starting the engine.
3. Keep your keys in position '2.' Wait 30 seconds to allow your dash lighting system and vehicle computer to adjust. Press your foot on the brake pedal.
4. Turn your BMW 325Ci off so that the system can register repairs that have occurred since your brake warning light first appeared.
5. Turn your keys all the way clockwise in the ignition to restart your 2001 BMW 325Ci. View your dashboard lighting system. Check to make sure the brake warning light is off to ensure that your system is reset.
Continue lendo

How to Tell If an Audi Has Servotronic


1. Open the driver's door and locate the fuse panel on the left side of the dashboard.
2. Insert the flat screwdriver into the small slit on the fuse panel and pry it loose.
3. Look inside the fuse panel, behind the fuse box, for the Servotronic module. It will be marked with a '638' stamp or 'Servotronic' marking. If the module is not there, then your Audi does not have Servotronic.
Continue lendo

How to Replace the Alternator in a Mercedes Benz


1. Examine the drive belt configuration. The Mercedes Benz line of vehicles uses a serpentine belt (one long belt) to power the alternator and a series of other electrical components. Note the orientation of the belt. There is a belt diagram on the underside of the hood and on the frame of the Benz next to the hood latch (on some models).
2. Release tension on the alternator belt. Turn the center tension pulley clockwise with a socket wrench. This will create slack in the belt.
3. Slide the belt off the alternator. You will need to remove the belt from all of the other components on the system as well.
4. Remove the electrical connector on the back of the alternator.
5. Remove the top and bottom alternator mounting bolts and slide the alternator out of the engine bay.
6. Install the new alternator. Installation is the reverse of the removal process. When installing the belt, it is best to use a new one. They're relatively inexpensive for the Benz and by the time an alternator needs to be replaced, the belt is usually worn to the point where it will likely need to be replaced soon as well. Make sure that the belt sits directly in the center of the pulley, and that the teeth on the belt sit in the pulley's grooves. Route the belt according to the belt path on the underside of the hood.
Continue lendo

How to Reset a Fuel Gauge


1. Turn the ignition switch to the 'On' position.
2. Press the 'Odo/Trip' button until the odometer is put into 'ODO' mode.
3. Turn off the ignition.
4. Press and hold the 'Odo/Trip' button. Turn the ignition switch to the 'On' position. Hold the 'Odo/Trip' button for two seconds. Release the 'Odo/Trip' button and then immediately press it again, release it, press it, release it and then press it and hold it. Hold the button until the leveling information is displayed on the odometer, about five seconds.
5. Release the 'Odo/Trip' button.
6. Press and hold the 'Odo/Trip' button until the odometer display reads '1', which indicates the reset process has begun.
7. Release the 'Odo/Trip' button when the reset process is complete, which is indicated when the odometer display returns to normal.
8. Turn off the ignition.
Continue lendo

How to Charge a Cold Car Battery


1. Remove the drained battery from your vehicle. You'll need to use the correct size wrenches to loosen the terminals and remove any shields or brackets that are holding the battery in place.
2. Place the battery in a well-ventilated environment where the battery can slowly warm above freezing. Do not place the battery near open fire or heat. Remember, you'll have to use your battery charger, so a nearby electrical outlet and/or extension cord will be necessary.
3. Check the battery for physical damage after you've allowed it warm up. If it's a standard-duty battery, remove the caps and check the water level. Add distilled water if necessary; just enough to fill the bottom of the refill holes. Once you've made sure the battery is full of water and is undamaged, you can proceed with recharging it.
4. Check your battery charger to make sure all switches are off. You can also check to make sure it is set to 12 volts. Then hook the positive clamp of the charger to the positive post on your drained battery. Hook the negative clamp to the negative post in the same manner.
5. Plug your battery charger into a nearby electrical outlet, using an extension cord if necessary.
6. Adjust the settings on your battery charger, if any. Some chargers allow you to set the amp-rate at which the battery charges. The higher the amps, the faster your drained battery will recharge. Some chargers also have a timer. Set the charger according to your wishes and turn the power on. Charging times will vary, so check on the battery often.
7. Unplug the charger once the battery has a complete charge. Turn the switch off and unhook the negative clamp, then the positive clamp.
8. Place the battery back into your vehicle, making sure you fasten the terminals securely to the battery posts. Replace all shields and brackets and start your vehicle.
Continue lendo

Mercedes Benz C230 Won#039;t Start


1. Add 1 gallon of gas to your C230 and then turn the key in the ignition on and off a couple of times while you are pumping the C230's gas pedal. This will engage the car's fuel pump.
2. Turn the ignition and listen for a clicking noise. Have a mechanic check the starter if you hear a clicking noise
3. Turn the ignition over without starting the car. Check the electrical lights in your car's dashboard. If the lights do not come on or the lights are really dim, the battery needs to be charged or replaced.
4. Jump start the C230 with another car and a pair of jumper cables. Allow the car to run for about 5 minutes and then turn it off. Try to restart the car. If the car will not turn back on, you need to replace the battery.
Continue lendo

How to Change a BMW Door Handle


1. Remove the plastic cap that conceals the screw that holds the housing to the door panel. Use a flat head screwdriver to pry the cap off.
2. Remove the screw that holds the door handle housing to the door panel with a screwdriver. The housing should now come loose.
3. Pull the housing gently away from the door panel. The door handle will still be connected to the release cable, so only pull it as far as the cable will allow you to.
4. Disconnect the door release cable with a pair of long needle nose pliers. The cable is fastened with a hook that needs to be wiggled and pulled off of the large metal hook on the door handle. You should now be able to remove the door handle and housing from the door panel and set it aside.
5. Install the new assembly by hooking the door release cable over the hook on the new door handle assembly. It will help to turn the housing 180-degrees (upside down) and hook the cable on. Once the cable is hooked on, turn the assembly back around, being careful not to scratch the leather.
6. Place the housing partially back in the door panel. Place the cable in the guide groove of the housing. This cable must be installed in the groove in order for the door to open. Push the door handle into place in the door panel.
7. Reinstall the screw that holds the door handle housing to the door panel. Reinstall the plastic cover that conceals the screw. Test the door handle to ensure that it is working correctly.
Continue lendo

How to Connect to a 745i With an iPhone


1. Turn on your iPhone and turn on Bluetooth by selecting 'Settings > General > Bluetooth' and switching the toggle to 'ON.' This will allow you to make phone calls using the phone icon on your 745i's steering wheel.
2. Connect your iPhone to the USB port located at the left of your 745i's glove compartment using the iPhone USB cord.
3. Push down the iDrive control wheel at the center of your console to activate the iDrive display to the right of your steering wheel. Your iPhone's playlists and artists will be displayed on the screen.
4. Use the iDrive control wheel or the steering wheel's arrow buttons to scroll through playlists, artists and tracks. Tap the phone button on the steering wheel and use the iDrive control wheel to scroll through contacts and make phone calls.
Continue lendo

How to Replace an Oil Pan Gasket in a Mercedes Benz E320


1. Remove the oil pan from underneath the engine. Wash the pan and bolts with soap and water to remove any oil residue. Dry both the pan and bolts completely with a rag before moving on to the next step.
2. Line the gasket ridge and bolt holes on top of the drain pan with a rubber sealant. Arrange the gasket on top of the pan by lining up the bolt holes. Press the gasket down firmly. Place the bolts in the holes to hold the gasket in place and to ensure they go through easily.
3. Allow the pan and gasket to dry for at least 30 minutes before reattaching it to the transmission casing.
Continue lendo

How to Turn on Sirius Satellite Radio


1. Load the Sirius Satellite Radio activation page, located at sirius.com/install. Alternatively, you can call the Sirius customer service hotline at (888) 539-7474.
2. Power on your satellite radio and tune it to channel 184.
3. Click the 'Activate Now' button on the Sirius activation website. Be certain to take note of your Sirius receiver's Electronic Serial Number (ESN) before starting the activation process.
4. Click the 'Get Started' link under the Create a New Account heading.
5. Enter the ESN in the appropriate field, and type the promo code for your account, if you have one. Select where you are activating the radio, and type the security code shown in the verification image. Click 'Next' after providing this information.
6. Create a username and password for your Sirius account on the Account Login page. Click 'Next.'
7. Provide the contact information, including address and phone number, for the account holder, and click the 'Next' button after providing this information.
8. Enter your gift card number if you are paying for the full subscription or a portion of it using a Sirius gift card. Click 'Next' after providing the gift card number, if applicable.
9. Select the Sirius radio package you want to turn on. Sirius offers a range of packages, including Sirius Everything, which includes all Sirius channels, Sirius with the Best of XM, which adds popular XM channels to your receiver, and even special interest packages where you can choose up to 50 channels to include with your subscription. Click 'Next' after selecting a package.
10. Provide billing information, including a credit card number, to configure automatically recurring payments. Click 'Next.'
11. Review your new account details and click the 'Activate' button to turn on Sirius Satellite Radio. Ensure that your radio is tuned to channel 184.
Continue lendo

How to Change Oil on Car Ramps


1. Place the car ramps on a firm, level surface in front of the car. Line the ramps up to the same width as the front tires on the car.
2. Carefully drive the vehicle up onto the ramps, stopping on the flat section at the top. A second person to help guide you up can be helpful, but is not required.
3. Place wheel chocks or a block of wood behind the rear wheels of the car to keep it from rolling.
4. Open the hood of the car and remove the oil fill cap on the engine. Setting it on the top of the engine will remind you that you have not refilled the oil. Do not put the cap back on until you do so.
5. Place an oil drain pan under the oil pan drain plug and carefully remove the plug using an appropriately sized socket and ratchet. You may need SAE or metric sockets depending on the make and model of the car. The best way to find out what size you need is to check a repair manual for your car or try a few different ones until you find one that fits.
6. Allow the oil to drain into the drain pan. It won't take too long to drain. The average car holds 4 to 5 quarts of oil.
7. Locate the oil filter on the engine block. You will need to decide what kind of filter wrench you want to use, but band clamp filter wrenches are typically very effective.
8. Place the oil pan drain plug back into the pan and tighten it until it is just snug. Move your drain pan under the oil filter and remove the filter. Turn the filter upside down and set it into the pan for now.
9. Open one quart of the new oil you will be using. Wipe a small amount of the fresh oil onto the filter gasket of the new filter. This will help it seal and keep it from sticking when you are ready to change it again.
10. Pour the contents of the quart of oil into the top of the oil filter until it is full. Filling the filter reduces the stress of the oil pump and engine when you first start it after a complete oil change.
11. Screw the filter into place on the engine by hand. Do not use a wrench on the new filter. It will seal fine being hand tightened. Over-tightening will make it hard to get off at the next oil change.
12. Fill the engine with the remaining oil but do not overfill it. If you are not sure what the oil capacity of your motor is, check your owner's manual or shop manual. You can also add a quart at a time and then check the dipstick to monitor your progress.
13. Replace the oil fill cap and check under the car for any leaks. Tighten anything that is leaking before taking the car off the ramps.
14. Close the hood and remove the wheel chocks. Slowly back the car off the ramps and dispose of the waste oil and old filter.
Continue lendo

How to Change Brakes on a Mercedes C280


1. Park your car and turn off the engine. Elevate the car using a jack and support stands. The stands should be positioned under the pinch welds under the front doors.
2. Use a lug wrench to loosen the lug nuts on a wheel, then remove them one by one.
3. Remove the caliper mounting bolts with a Torx wrench before taking the brake caliper from the rotor to disassemble the caliper assembly. Attach it to the coil springs with some zip ties. Take off the brake pads by striking them gently with a rubber mallet.
4. Use a C-clamp to push the caliper piston into the caliper. It should fold accordian-style back into the caliper housing. Place the new brake pads into the caliper. Reassemble the caliper assembly. Repeat the process on the other wheels.
5. Replace the wheels and lower your vehicle. Don't forget to tighten the lug nuts with the lug wrench.
Continue lendo

How to Change the Temperature in the BMW 325xi


1. Turn the dial located to the left of the 'Auto' button clockwise to increase the temperature on the driver side.
2. Turn the same dial counterclockwise to decrease the temperature on the driver side.
3. Turn the dial located to the right of the recirculated air button clockwise to increase the temperature on the passenger side.
4. Turn the same dial counterclockwise to decrease the temperature on the passenger side.
Continue lendo

How do I Get the 2008 Audi R8 in Midnight Club Los Angeles?


1. Sign up for a Rockstar Social Club account on the official website. Click 'Sign Up' and submit your personal information to create a free account. You can then begin to complete the following challenges.
2. Get $1,000,000 of cash in-game. This challenge requires the player to win enough street races to accumulate $1,000,000. Playing harder races yields more prize money when winning, and can speed up the process.
3. Drive 5,000 Miles in-game. This challenge simply requires the user to drive their cars in-game for a lengthy amount of time. Some users simply leave their game running while holding on the acceleration button to avoid sitting in front of the TV for excessive time.
4. Get 25 Consecutive Wins. From the title screen menu, select 'Arcade Mode'. The user must win 25 consecutive races in order to achieve this challenge.
5. Drive 10 Miles on Two Wheels. Press and hold on the 'B' button (Circle on PS3) and hold the Right Analog stick to the right or left to drive your car on two wheels. Continue this two-wheel driving for ten consecutive miles to achieve this challenge.
6. Drive a 15 mile wheelie on a motorcycle. Press and hold the 'B' button (Circle on PS3) and press the right analog stick downward to drive your motorcycle in a wheelie. Hold the wheelie for 15 consecutive miles to complete the challenge.
7. Cruise for 25 hours in-game. Simply drive your cars for 25 hours on the streets in-game. Races do not count as driving time for this challenge.
8. Total your car 5,000 times in-game. To complete the challenge, get into 5,000 accidents in-game by crashing at high speeds to wreck your car.
9. Jump 200 meters with your car or motorcycle. To achieve this challenge, drive your car or motorcycle off a large ramp that will give you a large jump distance.
10. Win 350 races in career mode. On the title screen menu, select 'Career' and complete 350 races against other drivers to complete the task.
11. Destroy 250 of your vehicles in-game. This task is very similar to the vehicle total challenge. Simply drive your car or motorcycle into the water or a gas tank to flood or explode your vehicle.
12. Hit 1,000 opponents while driving in-game. This challenge does not limit you to hitting opponents while just cruising on the street; you can also hit them during a race.
13. Hit 10,000 objects in-game. Drive your vehicle around the streets to hit various objects, such as mailboxes, bus stops and garbage cans.
Continue lendo

How to Set Up Bluetooth in a Mercedes


1. Press the 'Tel' key on your Mercedes radio or select the 'Phone' menu from your vehicle's navigation menu.
2. Select the 'Phone' button on the lower left corner of the screen.
3. Select 'Phone List,' 'Options' and 'External Authorization.' This places your Mercedes into pairing mode.
4. Go to your cell phone's Bluetooth menu and add a new device. This process will vary depending on the type of phone you're using. Refer to your phone's manual for specific instructions.
5. Select 'MB Bluetooth' as the device that you want to add to your phone.
6. Confirm on your Mercedes that you want to authorize your phone to be paired with your vehicle.
7. Enter a unique password from one to 16 digits. Mercedes recommends that your password be at least four digits long.
8. Enter the same password on your phone when prompted.
9. Select 'Yes' on your Mercedes when it says, 'Accept connection request from MB Bluetooth®?' This will complete the pairing process and you will be able to use your phone hands-free in your Mercedes.
Continue lendo

How to Draw a Three


1. Draw an equilateral triangle with one side of the triangle horizontal and at the top.
2. Draw an isosceles triangle directly on top of this equilateral triangle. An isosceles triangle is a triangle that has two equal sides. This will be the top point of your star.
3. Turn your paper to the right so the far right side of the equilateral triangle is a horizontal bar at the top. Draw an isosceles triangle at the top of this side, identical to the first one your drew.
4. Turn your paper to the right again so the final side of the equilateral triangle is a horizontal bar at the top of the paper. Draw another isosceles triangle on top of that, exactly the same size and shape as the previous ones you drew. You will now have a three-pointed star.
Continue lendo

How to Reset the Service Indicator Light on a Mercedes Benz GL450


1. Insert the key in the ignition. Move the ignition switch to position I.
2. Press the left or right menu button on the display until the mileage is displayed on the screen. The menu buttons are located directly above the display screen.
3. Press the 'Reset' button quickly three times. The reset button has an 'R' on it.
4. Press the up or down arrow until the service menu appears on the display.
5. Press the left or right button until 'Confirm' is selected on the screen.
6. Press the 'Reset' button once to reset the service indicator.
Continue lendo

How to Reset a Mercedes Key Fob


1. Put your key in the ignition of your Mercedes-Benz and push and hold the lock button while the key is in the ignition. Do not turn on your vehicle during this process and do not let go of the lock button.
2. Remove your car key from the ignition while you are still holding the lock button. Click the unlock button on the fob five times, still holding down the lock button.
3. Remove your finger from the lock button and your key should be reset. Test your key fob to ensure that it works.
Continue lendo

How do I Replace the Door Trim on an Audi 100 CS?


1. Open up the door of your Audi 100 CS which you will be removing the trim from.
2. Slide the trim stick in to the door frame. Pry the trim away from the door frame with the stick. Once it comes loose from the door, pull it completely away with your hands.
3. Use a Phillips screwdriver to remove the screws which are attached to the door handle trim. Pull the trim away from the door.
4. Remove the mounting screws which fix the trim around the inside of the door panel and around the automatic window control. Pull them both from the door to complete the work.
5. Place the new door panel trim on to the door panel with your hands. Secure it on the connectors around the door and fix in place with screws using a screwdriver.
6. Place the door handle trim carefully around the edges of the door handle. Attach the screws to fix it firmly in place.
7. Carefully fix the trim around the outer door frame. Hook the trim around the connectors to secure it in place. Take care not to damage the window in any way. Press around the edges of the window with your hand to ensure it is fixed securely to the door.
Continue lendo

How to Replace the Oil Pan on a Mercedes 190e


1. Lift the front of the Mercedes 190e with a floor jack and place jack stands under the front axle on both sides of the car, then lower the vehicle to rest on the jack stands.
2. Locate where the exhaust pipe attaches to the engine and detach the pipe from the motor, using a socket wrench to unfasten the bolts.
3. Remove the air filter canister by undoing the bolt on the top with a socket wrench and taking the canister off the top of the engine.
4. Disconnect the linkage to the carburetor with a pair of pliers and move the linkage out of the way.
5. Unfasten the motor mounts of the engine, using a socket wrench to remove the bolts, then lift the engine up with a floor jack about 4 inches.
6. Place two wood blocks between the engine and the vehicle frame to hold the engine in place then lower the floor jack away from the engine.
7. Locate the oil pan drain plug on the bottom of the oil pan and place a drip pan underneath the drain plug.
8. Loosen the drain plug with a socket wrench and allow the oil to drain into the pan until it is completely empty.
9. Move the drain pan out of the way and unfasten the bolts on the oil pan with a socket wrench.
10. Pry the oil pan from the engine block with a screwdriver, moving the oil pan out from under the engine then use a putty knife to scrape off any excess gasket material from under the engine.
11. Place the new oil pan gasket on the lip of the new oil pan and slide the pan into position, attaching it with bolts to the bottom of the engine.
12. Lift the engine up with the floor jack, remove the wood blocks then lower the engine back into position over the engine mounts.
13. Secure the engine to the engine mounts, using a socket wrench to tighten the nuts then reattach the carburetor linkage.
14. Secure the air filter canister back into place and reattach the exhaust pipe to the engine.
15. Raise the vehicle up off the jack stands and remove the stands, lowering the car back onto the ground.
16. Locate the oil cap on the top of the intake manifold and take the cap off.
17. Fill the engine with five quarts of oil then place the cap back on the intake manifold.
Continue lendo

How to Pair Your Bluetooth Phone with Your BMW 3 Series, X3, X5, Z4, M3 and M Roadster


1. Start your BMW. It will automatically be in pairing mode for the 2 minutes after it is started.
2. Go to the connections menu in your Bluetooth enabled phone and select "search for devices"
3. You should see an ID appear on your phone that starts with BMW. Select this device ID.
4. Enter the passkey. Once prompted you will only have 20 seconds to complete the task.
5. Now check the radio display. It should indicate that the pairing process was successful. At this point your data will be downloaded into the cars system.
6. Confirm that your contacts have been loaded into the system and perform a test call.
Continue lendo

How do I Remove the Driver Door Mirror From a C32?


1. Open the driver's side door as far as it will go and locate the triangular cover secured to the inner door panel. The cover is located directly opposite to the spot where the mirror is attached on the outside of the door.
2. Pull the access cover off the inner door panel, using your fingers.
3. Pull the wiring harness out of the inner door and disconnect it.
4. Remove the three bolts that secure the mirror to the door frame, using a socket and ratchet.
5. Pull the mirror straight out from the door to remove it.
Continue lendo

How to Change the Fuel Filter on 2001 Passat


1. Park the Passat on a flat surface. Raise the rear with the floor jack and lower it securely onto jack stands. You can also drive the back tires up on ramps to gain access to the filter. Never work under a car when it is only supported by a floor jack.
2. Locate the skid panel that protects the underside of the car; it is on the driver's side at the back of the car. Remove the four nuts around the perimeter of the panel with a socket and a ratchet. Remove the Phillips screw in the middle of the panel. Set the panel out of the way.
3. Remove the two bolts that hold the bracket for the fuel filter. The filter is cylindrically shaped. Squeeze the bracket with your hand once the two bolts are removed to loosen and remove the bracket. The filter should fall free.
4. Squeeze the fuel line from the gas tank that goes into the filter with the vise grips to prevent fuel from spilling when it is removed. Loosen the hose clamps that hold the fuel lines to the filter on either side, one that comes from the tank on one side and one that comes out of the filter on the other side that goes to the engine. Depending on the type, the clamps may be loosened with a screwdriver or by squeezing them together with a pair of pliers.
5. Install the new filter with the arrow on the filter facing toward the engine. Slide the fuel lines onto the filter on either side and tighten the hose clamps. Reinstall the fuel filter bracket with the two bolts and the screw that hold it on. Reinstall the skid panel. Start the engine to make sure there are no leaks. Lower the car back to the ground or drive it down off the ramps.
Continue lendo

How Do I Fix a Water Pump on a 1992 BMW 325i?


1. Ensure that the engine is cold. Lift the front of the car with a floor jack and lower it onto a pair of jack stands. Turn the heater controller (or press the buttons if electronically controlled) to hot and turn the ignition key to the “On” position.
2. Place a container under the passenger side of the engine under the manifold. Loosen and remove the coolant drain plug, located in the block just below the manifold. Drain all of the coolant from the engine. Install and tighten the drain plug with a new sealing ring to 18 foot-pounds.
3. Move the coolant container under the radiator. Loosen and remove the plastic drain plug at the bottom of the radiator and drain the coolant. Reinstall the drain plug and tighten it to 2.2 foot-pounds. Do not over-tighten it.
4. Pry the cap off of the belt tensioner. Loosen the belt tensioner for the poly-ribbed belts with a socket or the appropriately sized Allen wrench. This may turn in either direction, depending on the type of tensioner, so loosen it in both directions to see how it loosens. Slide the belts around the fan, nearby components and out of the engine.
5. Remove the small plastic rivets that hold the fan frame to the radiator by prying them up and out very carefully with a screwdriver. Disconnect the coolant reservoir hose where it goes to the engine near the water pump. Disconnect the coolant overflow hose. Remove the fan, fan frame and coolant reservoir at the same time.
6. Remove the four small nuts that hold the fan pulley to the water pump with a socket and ratchet. Loosen and remove the four bolts that hold the water pump to the engine. Remove the water pump from the engine bay. Tap it lightly with a hammer if needed.
7. Clean the bore in the engine where the water pump installs so there is no debris. Clean it with a wire brush as well. Install the new water pump with a new O-ring. Place a layer of white lithium grease on the O-ring to ensure a good seal. Install the water pump and tighten the bolts to 8 foot-pounds. Bolt the fan pulley onto the new water pump.
8. Reinstall the fan, fan frame and coolant reservoir. Reinstall the plastic rivets that hold the fan frame to the radiator. Reinstall the belts. Tighten the belt tensioner.
9. Remove the small plastic bleed screw located to the right of the radiator cap. Place a funnel in the expansion tank and fill the cooling system very slowly with new coolant. Use 10 quarts for the 325. Continue filling until coolant comes out of the bleed screw. Fill until there are no air bubbles coming out with the coolant. Wipe up spilled coolant. Tighten the bleed screw to 71 foot-pounds. Run the engine and top up the coolant if necessary.
Continue lendo